Pages

Sunday, July 24, 2011

Insect Slide Preparation for Microscope Examination

My first attempt of insect slide making was not a successfully one but I think the experience worth to share, especially for those DIY hobbyists.  I was very excited to find an insect slide making reference published by Schauff from USDA.  The Schauff's protocol can be generalized by the following steps:

1) Maceration (cleaning): Using caustic reagents, such as sodium hydroxy, potassium hydroxy, lactophenol or lactic acid , to remove external secretions, foreign matters, some organs, and fat bodies.  The purpose is to remove those parts without damaging the chitinous parts.  Heating the specimen in the maceration reagent can accelerate the process. 2) Washing: Removing the caustic agents with tap water in a small dish for at least a few minutes.  3) Staining, Bleaching and Dehydration: Staining and bleaching are optional steps to improve the viewing ability of the insect.  Stain it, if too light.  Bleach it, if too dark. Any residual water in the specimen needs to be removed before mounting - it is not mixable with water.  4) Mounting: Mounting for microscopic examination can be temporary or permanent. temporary slide can be made with acetic acid on a cavity slide.  The permanent mount can be done with Canada Balsam, Euparal or Hoyer’s medium and polyvinyl alcohol (PVA).

In this trials, aphids an ants (that protects the aphids) found on my loquat tree were chosen to make the microscope slides because they are readily available from backyard.  My protocol adopted Schauff's protocol but slightly modified and using the generally available household chemical.  :

1) Maceration: This step is done with 10% sodium hydroxy solution. To make the solution, I added 1 gram of Roebic heavy duty crystal drain opener (Picture on the Left) in 10 mL tap water. The Roebic Heavy duty crystal drain opener contains 100 percent sodium hydroxy, according to the manufacturer's MSDSOLYMPUS DIGITAL CAMERAThere are other types of drain opener in the home improvement store, but this is the only one contains one hundred percent sodium hydroxy. Candle warmer container is used for the maceration.  The sodium hydroxy will gradually turned yellow when it started to digest the insect’s internal organs (Right).  I varied the length of maceration from 24 to 72 hours – the longer I left the insects in sodium hydroxy, the more transparent they are.

2) Cleaning: The insects were picked up by a pair of tweezers and transferred to tap waterinsect_slide_making_cleaning.  I gently pipetted the contents to allow sodium hydroxy to be diluted faster.  I repeated it for the second time by siphoning up the supernatant. The supernatants were discarded and the insects were left in the in the container.  Another 10 to 15 mL tap water was added and repeat the some process.  The insects are now partially transparent but still has some contents in the abdomen and thorax.

 

3) Dehydration and more cleaning: This step is done by Crown Denatured Alcohol Next which contains about OLYMPUS DIGITAL CAMERA95 percent ethanol (The rest of the ingredient is isopropanol) – Crown has another denatured alcohol contains methanol.  I like the one labeled as “Next” and “95 Percent nature content” because ethanol is less toxic.  Again, I siphoned water from the cleaning solution and left the insects in the candle holder then added 10 to 15mL denatured alcohol. The container of alcohol wasn’t helping me to pour the alcohol out.  I used the funnel to help but it still got messy.  Cloud formation during alcohol dehydrationThe insects were left in alcohol for about 30 minutes then I started the cleaning.  This time was the internal organs of the insects.  There are still plenty of contents resided in the exoskeleton of the insects and surrounded the carcasses – I believed that they were denatured proteins an nucleic acids which were precipitated out then I added alcohol.  I cleaned them up with a pair of picks.  I siphoned the cleaned insects up and transferred it to a different container containing the denatured alcohol.  I did more cleaning after the transfer to remove any protein and nucleic acid residues (right).

4) Mounting: The insects were siphoned up and transferred to a microscope slide.  I tried to picked up as little alcohol as possible so that the alcohol won’t spill over or messed up the insects already on the slide (Several insects were mounted on the same slide and in different position).  The position and the posture of the insects were manipulated with picks to optimized the viewing – extending legs, minimized the wrinkles, changed orientations, making the posture natural etc. A few drops of clear fingernail polish top code were added to the slide to cover the insects.  A cover slip was placed on the top to finish the mounting.  I waited overnight to allow the finger nail polish to harden before viewing on the microscope.

The following are the pictures from the insect slides made from this experiment:  Because this was my first attempt to make insect slides, it’s an trial and error process, not all pictures are using the same condition.  In the future post, I will summarize the process and post the optimized condition.  For example: Some slides were made with 24 hours of maceration, it tends to show more internal organs and less transparent.  The aphid body tends to show better skeleton when they were processed with longer maceration.  They also varied with degree of cleaning.  The aphid bodies contain lots of fluids and rich in protein.  They tend to become less transparent when immerged in alcohol,.  The body contents needs to be squeezed out with a pair of picks.  Some specimens were not cleaned too well which leaved body parts in the specimen while others were cleaned very well but the extensive cleaning caused the body to be broken apart.

The ants seem to be easier to process then the aphids because of harder exoskeleton. They don’t disintegrated like the aphid’s body do.  They don’t have lots of body fluids.  This makes the cleaning much easier then the aphids.

Some suggestions about insect slide making:

  • The protocols can varied among different insects.  Some insects have harder exoskeleton and can resist harsher processing condition while other were softer which required gentler processing condition.  For example, some insect can allow to be boiled in NaOH solution while others can only left in room temperature overnight.  Some required extra physical cleaning while others can only resist chemical cleaning.  The body size can also determine how much processing time.  Some insects are so big that you need to punch a hole between segments to allow reagent to penetrate.
  • To accelerate the maceration process, some gentle heating might be required (Note: if you are heating the NaOH, make sure that you used a container that can allow direct heating.  The candle holders used in this experiment are not.  I actually blow up a candle holder by putting it on the top of the 900 W outdoor food warmer!  An electronic candle warmer might be used.)
  • If you need to squeeze out the body content, do it during cleaning step rather than dehydration step.  This will minimized the amount of body fluid denatured in the alcohol – less cleaning.
  • Use siphon suck up the insect along with some liquid that the insects are in.  This might work better than tweezers or picks, especially after you squeeze the body content out.  The body is very fragile.
  • Take your time.  Be patient and gentle.
  • Use Canada balsam if available – I think this is give or take.  The advantage of using Canada balsam is the color less and less shrinking than finger nail polish top coat but it required Xylene for dehydration.  Xylene is very toxic.  While the finger nail polish shrink a lot but you can put insect in ethanol directly in finger nail polish top coat without any problem.
  • Use concaved slides or build some wall on the slide to allow more depth if you are doing the whole insect mount.

Reagents, contains and tools can be found in your home.  If not, they can be easily found in the home improvement stores (such as Lowes or Homedepot), dollar stores or grocery stores.  I’ve found many of these can be found at Amazon.com. (The only thing that I could not find there is the Crown denatured alcohol (which contains 90-95% Ethanol and 5-10% isopropanol.  Amazon only has reagent grade ethyl alcohol.).

10 comments:

  1. Hi there,

    I really need this explanation which comes with photos. FYI, I'm currently working with Lepidopteran larvae for my master research. I need to observe the chaetotaxy of the larvae, which I need to do mounting. I just wanna know if for larvae, which slide do I need to use? The normal flat slide or the one with well. And some of the larvae are quite big, so do you know how to mount them? I really don't get the idea. Because no one here in my department knows the mounting technique. Maybe you can help me on this.

    Anyway, what is the title of the book written by Schauff you mentioned above? Maybe I can get one in Malaysia if available.

    Thanks!

    ReplyDelete
  2. You need to use the slide with a well or make the well yourself. (The common concaved slides are not deep enough for insects.) The book can be downloaded from USDA website at http://www.ars.usda.gov/SP2UserFiles/ad_hoc/12754100CollectingandPreservingInsectsandMites/collpres.pdf

    ReplyDelete
  3. This topic was your advantage among other blogs out there. This blog contains and provide definitely unique ideas and information specially on the field of microscopy.

    ReplyDelete
  4. What a great Blog! And, a very informative post. I'll be trying to make some of these slides today, and went searching for tips & info. My specimens have been soaking in various preservative solutions for many years - So, they're ready!
    And, thanks to Small World for the comment! Using well slides, and especially, making my own wells is something I want to learn more about. I presume we've all seen the beautiful results obtained by slide makers in London, circa 1800's etc. :)
    Again, this is an excellent post! Thanks!

    ReplyDelete
  5. Interesting topic, Your topic is really good it inspire me more to revisit your site more often. Thanks for sharing!

    Android Microscope Mount

    ReplyDelete
  6. I had visited your website which was really good PREPARED MICROSCOPE SLIDES

    ReplyDelete
  7. I think this is one of the most significant information for me. And i’m glad reading your article. But should remark on some general things, The web site style is perfect, the articles is really great : D. Good job, cheers
    pest control san antonio
    #pestcontrolsanantonio

    ReplyDelete
  8. I am very glad that i had the chance to learn more about practical microscopy, i can remember using a microscope in my science related practical sessions. I am glad that they can also be used in other ways, making this post very informative. While doing your practicals, you will need a clear and clean place. Why not buy a Medium Desk Organizer to keep your important items well organized.

    ReplyDelete
  9. I really loved reading your blog. It was very well authored and easy to understand. Unlike other blogs I have read which are really not that good.Thanks alot! easy trap zanzare

    ReplyDelete
  10. Thanks for a wonderful share. Your article has proved your hard work and experience you have got in this field. Brilliant .i love it reading. fumiganti insetticidi

    ReplyDelete